Datalogic DS2100N Manuel d'installation

DS2100Installation Manual

viii Warning labels indicating exposure to laser light and the device classification are applied onto the body of the scanner (Figure A, 6).

ix POWER SUPPLY - This product is intended to be installed by Qualified Personnel only. - Models DS2100-X0XX, DS2100-X1XX: This accessory device i

x

GENERAL FEATURES 1 1 1 GENERAL FEATURES 1.1 INTRODUCTION The DS2100 laser scanner satisfies the most advanced needs of a wide range of users. It h

DS2100 2 1 • programmable in 4 different operating modes to suit the most various barcode reading system requirements. • code verifier • low pow

GENERAL FEATURES 3 1 1.4 AVAILABLE MODELS The DS2100 scanner is available in versions that differ in regard to the following parameters: • Resolut

DS2100 4 1 1.5 GFC-2100 ACCESSORY INSTALLATION GFC-2100 is a 90° deflection mirror available on request for DS2100. The installation of the 90° d

INSTALLATION 5 2 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the DS2100 reader and all the parts supplied with the equipment are present and i

DS2100 6 2 2.2 MECHANICAL INSTALLATION DS2100 can be installed to operate in different positions. The four screw holes (M4 x 5) on the body of the

INSTALLATION 7 2 2.3 ELECTRICAL CONNECTIONS Several DS2100 models are equipped with a cable terminated by a 25-pin female D-sub connector for connec

DS2100Installation Manual

DS2100 8 2 Pin RS232 RS485 full-duplex RS485 half-duplex 20mA C.L. (INT-22 only) 2 TX232 TX485+ RTX485+ CLOUT+ 3 RX232 RX485+ CLIN+ 4 RTS232 TX4

INSTALLATION 9 2 2.3.1 Power Supply Power can be supplied to the scanner through the pins provided on the 25- or 9-pin connector used for communicat

DS2100 10 2 RS232 Interface The serial interface is used in this case for point-to-point connections; it handles communication with the host compu

INSTALLATION 11 2 STARTOF TRANSMISSIONENDOF TRANSMISSION+ VRTS- V+ VTX DATA- V+ VCTS- VDATATRANSMISSIONDATATRANSMISSIONC1C2C4C3C5TRANSMISSIONSTOPPEDE

DS2100 12 2 DS2100 25-pinTX485+2TX485-4RX485+3RX485RX485-5TX4857SGNDSGNDUSER INTERFACE+-+-+EarthGround Figure 9 - RS485 full-duplex connections R

INSTALLATION 13 2 In a Multiplexer layout or for slaves, the Multidrop address must also be set via serial channel by the WinHost utility or by ESC s

DS2100 14 2 20 mA Current Loop Interface (INT-22 Accessory Only) When the INT-22 accessory board is installed, the DS2100 is equipped with a 20 mA

INSTALLATION 15 2 2.3.3 Auxiliary RS232 Interface The auxiliary serial interface is used exclusively for RS232 point-to-point connections. The par

DS2100 16 2 Code Verifier If the DS2100 is used as a Code Verifier, it is possible to indicate to the scanner what code to store as the verifier c

INSTALLATION 17 2 EXT TRIG+ 1819+ 5VDS2100 25-pin EXTERNAL TRIGGER Signal V30 Vdc max. Vextor EXT TRIG +EXT TRIG -8 9 DS2100 9-pin EXT TRIG- Figure

DS2100 INSTALLATION MANUAL

DS2100 18 2 EXTERNAL TRIGGERDS2100 25-pin1819+ 5VVS925GNDGroundVor8975VSGNDDS2100 9-pinSignalEXT TRIG+EXT TRIG-EXT TRIG+EXT TRIG- Figure 18 - Input

INSTALLATION 19 2 2.4 POSITIONING The DS2100 scanner is able to decode barcode labels at a variety of angles, however significant angular distortion

DS2100 20 2 The Tilt angle is represented by the value T in Figure 22. Position the reader in order to minimize the Tilt angle. Figure 22 - Tilt

INSTALLATION 21 2 2.5.1 Point-to-Point In this layout the data is transmitted to the Host on the main serial interface. Host Mode programming can be

DS2100 22 2 2.5.2 Pass-Through Pass-through mode allows two or more devices to be connected to a single external serial interface. Each DS2100 tr

INSTALLATION 23 2 2.5.3 RS232 Master/Slave The RS232 master/slave connection is used to collect data from several scanners to build either a multi-p

DS2100 24 2 2.5.4 RS485 Master/Slave The RS485 master/slave connection is used to collect data from several scanners to build a multi-point or a m

INSTALLATION 25 2 2.5.5 Multiplexer Layout Each scanner is connected to a Multiplexer (for example MX4000) with the RS485 half-duplex main interface

DS2100 26 3 3 READING FEATURES The number of scans performed on the code by the DS2100 and therefore the decoding capability is influenced by the

READING FEATURES 27 3 For example, the DS2100 (350 scans/sec.) for a 25 mm high code moving at 500 mm/s performs: [(25/500) * 350] - 2 = 15 effectiv

DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy DS2100 Installation Manual Ed.: 10/2003 ALL

DS2100 28 3 3.3 PERFORMANCE The DS2100 scanner is available in different versions according to the reading performance. Version Max Code Resolu

READING FEATURES 29 3 3.4 READING DIAGRAMS DS2100-1XX0 (Standard Resolution, 350 scans/s) 21015432345(in)01 32106(in)45 7 890 20 40 60 80 100 120

DS2100 30 3 DS2100-2XX0 (High resolution, 350 scans/s) 10212(in)01 53(in)2401020304050 6070 8090100110120130(mm)6050403020100102030405060(mm)0.15

READING FEATURES 31 3 DS2100-1XX4 Testarossa™ 21015432345(in)01 32106(in)45 7 890 20 40 60 80 100 120 140 160 180 200 220 240 260(mm)120100806040200

DS2100 32 3 DS2100-2XX4 Testarossa™ - High Resolution 10212(in)01 53(in)2401020304050 6070 8090100110120130(mm)6050403020100102030405060(mm)0.12 m

MAINTENANCE 33 4 4 MAINTENANCE 4.1 CLEANING Clean the laser beam output window periodically for continued correct operation of the reader. Dust,

DS2100 34 5 5 TECHNICAL FEATURES DS2100-XXX0 DS2100-XXX4 Testarossa™ Standard ResolutionHigh ResolutionStandard Resolution High Resolution ELEC

TECHNICAL FEATURES 35 5 SOFTWARE FEATURES READABLE CODE SYMBOLOGIES • EAN/UPC (including Add-on 2 and Add-on 5) • Code 93 • 2/5 Interleaved • C

DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Ge

iii CONTENTS GUIDE TO INSTALLATION ...v GENERAL VIEW ...

iv 3.4 Reading Diagrams ... 29 4 MAINTENANCE ...

v GUIDE TO INSTALLATION The following can be used as a checklist to verify all of the steps necessary for complete installation of the DS2100 scan

vi GENERAL VIEW DS2100 Figure A 1234 8765Mounting HolesLaser On LEDGood Read LEDExternal Trigger LEDPower On / Data TX LEDWarning and Device

vii SAFETY PRECAUTIONS LASER SAFETY The following information is provided to comply with the rules imposed by international authorities and refer