Datalogic QLM700 Manuel d'instructions télécharger pdf (Page 118)

MATRIX 210™ REFERENCE MANUAL

108

For device replacement it is necessary to send the previously saved configuration (both

Configuration and Environmental parameters) to the new device. To do this select "Send

Configuration with Options" from the Device Menu and check the Environmental Parameters

checkbox:

In order to return a device to its absolute default parameters including Environmental

parameters, the following Send Default Configuration with Options" dialog must be used:

1 2 ... 113 114 115 116 117 118 119 120 121 122 123 ... 141 142

MATRIX 210™ 1
CONTENTS 3
REFERENCES 6
COMPLIANCE 7
HANDLING 8
GENERAL VIEW 10
1 RAPID CONFIGURATION 11
USB Models 13
RAPID CONFIGURATION 15
STEP 3 – AIM THE READER 16
STEP 7 – TEST MODE 23
Host Mode Programming 24
Alternative Layouts 24
Code Quality Verification 24
2 INTRODUCTION 25
INTRODUCTION 27
2.3 ID-NET™ 29
VISISET™ 33
Restore 34
Replacement 35
2.5.1 X-PRESS™ Functions 38
Test Mode (Function 1) 39
Aim/Locate (Function 2) 39
Setup (Function 3) 40
Learn (Function 4) 40
2.5.2 Diagnostic Indication 40
2.6 MODEL DESCRIPTION 41
2.7 ACCESSORIES 41
2.8 APPLICATION EXAMPLES 42
2.8.1 Document Handling 42
2.8.3 Direct Part Marking 43
3 INSTALLATION 46
3.2 MECHANICAL DIMENSIONS 47
INSTALLATION 49
CBX ELECTRICAL CONNECTIONS 51
4.1 POWER SUPPLY 52
4.2 MAIN SERIAL INTERFACE 52
4.2.1 RS232 Interface 53
4.3 ID-NET™ INTERFACE 57
4.3.1 ID-NET™ Cables 57
4.3.2 ID-NET™ Response Time 58
RX TX 62
Reference 62
USER INTERFACE 62
4.5 INPUTS 63
PH-1 Photocell (PNP) 64
Input Device 65
4.6 OUTPUTS 66
Output Device 67
Control Signal for LT-700 68
Power to External 68
Illuminator 68
4.8 USER INTERFACE - HOST 69
5.1 25-PIN CONNECTOR 70
5.3 POWER SUPPLY 71
5.4 MAIN SERIAL INTERFACE 71
5.4.1 RS232 Interface 72
Matrix 210™ 73
5.5 ID-NET™ INTERFACE 76
5.5.1 ID-NET™ Cables 76
Response Time (ms) 77
5.8 INPUTS 83
INPUT DEVICE 85
5.9 OUTPUTS 86
5.10 USER INTERFACE 88
6 TYPICAL LAYOUTS 89
6.2 PASS-THROUGH 92
6.2.1 Pass-Through on RS232 92
6.3 ID-NET™ 94
 BA600 ID-NET™ Out 95
 BA400 Ext. Power 95
 BA500 Trigger 95
 BA300 Service 95
Fieldbus Interface 99
6.4 RS232 MASTER/SLAVE 100
6.5 MULTIPLEXER 101
6.6 ETHERNET CONNECTION 102
TYPICAL LAYOUTS 103
6.7 USB CONNECTION 104
7 READING FEATURES 105
MATRIX 210™ REFERENCE MANUAL 106
READING FEATURES 107
8 SOFTWARE CONFIGURATION 108
8.3 STARTUP 109
8.3.1 VisiSet™ Options 110
SOFTWARE CONFIGURATION 111
8.4 CONFIGURATION 112
8.4.3 Calibration 119
8.6 STATISTICS 130
9 MAINTENANCE 131
10 TROUBLESHOOTING 132
11 TECHNICAL FEATURES 135
GLOSSARY 137
DECLARATION OF CONFORMITY 141

Commentaires sur ces manuels

Pas de commentaire

Datalogic QLM700 Manuel d'instructions Page 118

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau Datalogic QLM700