Datalogic QLM700 Manuel d'instructions Page 112
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MATRIX 210™ REFERENCE MANUAL
102
8
8.4 CONFIGURATION
Once connected to Matrix 210™ as described in par. 8.3, you can modify the configuration
parameters as follows:
1. Press the Calibration Tool button from the Main Menu. Matrix 210™ will download its
permanent memory configuration parameters with the default values (if it is the first time)
to VisiSet™. The Calibration Tool window will be displayed together with the Parameter
Setup window working in Interactive Mode (see par. 8.4.1 and par. 8.4.3).
2. Edit the Matrix 210™ configuration parameters according to your application
requirements.
3. Use the Calibration Tool to fine tune the reading performance. See par. 8.4.3.
4. Close the Calibration Tool window and disable the Interactive Mode by pressing the
interactive button.
5. Save the new configuration to the reader permanent memory by pressing the Send
button.
NOTE
Especially for lengthy configurations in Interactive Mode, it is always good
practice to periodically send the configuration to Permanent Memory to
avoid losing the configuration in Temporary Memory.
6. Close the Parameter Setup window and press Disconnect on the VisiSet™ menu bar
(see Figure 108) or launch Run Mode from the VisiSet™ Main menu.
Disconnect exits closing communication between Matrix 210™ and VisiSet™, and
causes Matrix 210™ to enter Run Mode. The disconnected reader serial port is now
available.
Run command does not close communication between Matrix 210™ and VisiSet™,
and causes Matrix 210™ to enter Run Mode. In this case the reader output messages
are displayed on the VisiSet™ terminal and the statistics are displayed in the
Statistics window (Statistics enabled).
- MATRIX 210™ 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- HANDLING 8
- GENERAL VIEW 10
- 1 RAPID CONFIGURATION 11
- USB Models 13
- RAPID CONFIGURATION 15
- STEP 3 – AIM THE READER 16
- STEP 7 – TEST MODE 23
- Host Mode Programming 24
- Alternative Layouts 24
- Code Quality Verification 24
- 2 INTRODUCTION 25
- INTRODUCTION 27
- 2.3 ID-NET™ 29
- VISISET™ 33
- Restore 34
- Replacement 35
- 2.5.1 X-PRESS™ Functions 38
- Test Mode (Function 1) 39
- Aim/Locate (Function 2) 39
- Setup (Function 3) 40
- Learn (Function 4) 40
- 2.5.2 Diagnostic Indication 40
- 2.6 MODEL DESCRIPTION 41
- 2.7 ACCESSORIES 41
- 2.8 APPLICATION EXAMPLES 42
- 2.8.1 Document Handling 42
- 2.8.3 Direct Part Marking 43
- 3 INSTALLATION 46
- 3.2 MECHANICAL DIMENSIONS 47
- INSTALLATION 49
- CBX ELECTRICAL CONNECTIONS 51
- 4.1 POWER SUPPLY 52
- 4.2 MAIN SERIAL INTERFACE 52
- 4.2.1 RS232 Interface 53
- 4.3 ID-NET™ INTERFACE 57
- 4.3.1 ID-NET™ Cables 57
- 4.3.2 ID-NET™ Response Time 58
- RX TX 62
- Reference 62
- USER INTERFACE 62
- 4.5 INPUTS 63
- PH-1 Photocell (PNP) 64
- Input Device 65
- 4.6 OUTPUTS 66
- Output Device 67
- Control Signal for LT-700 68
- Power to External 68
- Illuminator 68
- 4.8 USER INTERFACE - HOST 69
- 5.1 25-PIN CONNECTOR 70
- 5.3 POWER SUPPLY 71
- 5.4 MAIN SERIAL INTERFACE 71
- 5.4.1 RS232 Interface 72
- Matrix 210™ 73
- 5.5 ID-NET™ INTERFACE 76
- 5.5.1 ID-NET™ Cables 76
- Response Time (ms) 77
- 5.8 INPUTS 83
- INPUT DEVICE 85
- 5.9 OUTPUTS 86
- 5.10 USER INTERFACE 88
- 6 TYPICAL LAYOUTS 89
- 6.2 PASS-THROUGH 92
- 6.2.1 Pass-Through on RS232 92
- 6.3 ID-NET™ 94
- BA600 ID-NET™ Out 95
- BA400 Ext. Power 95
- BA500 Trigger 95
- BA300 Service 95
- Fieldbus Interface 99
- 6.4 RS232 MASTER/SLAVE 100
- 6.5 MULTIPLEXER 101
- 6.6 ETHERNET CONNECTION 102
- TYPICAL LAYOUTS 103
- 6.7 USB CONNECTION 104
- 7 READING FEATURES 105
- MATRIX 210™ REFERENCE MANUAL 106
- READING FEATURES 107
- 8 SOFTWARE CONFIGURATION 108
- 8.3 STARTUP 109
- 8.3.1 VisiSet™ Options 110
- SOFTWARE CONFIGURATION 111
- 8.4 CONFIGURATION 112
- 8.4.3 Calibration 119
- 8.6 STATISTICS 130
- 9 MAINTENANCE 131
- 10 TROUBLESHOOTING 132
- 11 TECHNICAL FEATURES 135
- GLOSSARY 137
- DECLARATION OF CONFORMITY 141
Produits connexes et manuels pour Mise en réseau Datalogic QLM700
(69 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels