Datalogic DS2100N Manuel d'utilisateur Page 1

MATRIX FAMILYSetup Procedure Using Programming Barcodes

Setup Procedure Using Programming Barcodes 6 1.2 FOR MATRIX 400™ AND MATRIX 410™ 1. Perform the setup procedures described in the Quik Referenc

Setup Procedure Using Programming Barcodes 7 5. The reader is programmed and the AutoLearn Mode ends. The green “ready” LED is on. READY SETUPFO

Setup Procedure Using Programming Barcodes 8 NOTE If it ever becomes necessary to return to a Point-to-Point (Stand Alone) configuration you can

Setup Procedure Using Programming Barcodes 9 1.4 NETWORK LAYOUT BARCODES  ID-NET™ M/S Synchronized - Master Ì$MSYN01$-HÎ Master + 1 Slave

Setup Procedure Using Programming Barcodes 10  ID-NET™ M/S Synchronized - Master Ì$MSYN09$-ÄÎ Master + 9 Slaves Ì$MSYN10$-GÎ Master + 10 Sl

Setup Procedure Using Programming Barcodes 11  ID-NET™ M/S Synchronized - Slave Ì$+SYN01$-kÎ Slave 1 Ì$+SYN02$-rÎ Slave 2 Ì$+SYN03$-yÎ Slave

Setup Procedure Using Programming Barcodes 12  ID-NET™ M/S Synchronized - Slave Ì$+SYN08$-5Î Slave 8 Ì$+SYN09$-<Î Slave 9 Ì$+SYN10$-jÎ

Setup Procedure Using Programming Barcodes 13  ID-NET™ M/S Multidata - Master Ì$MMUL01$-ÇÎ Master + 1 Slave Ì$MMUL02$-#Î Master + 2 Slaves Ì

Setup Procedure Using Programming Barcodes 14  ID-NET™ M/S Multidata - Master Ì$MMUL09$-TÎ Master + 9 Slaves Ì$MMUL10$-ÆÎ Master + 10 Slave

Setup Procedure Using Programming Barcodes 15  ID-NET™ M/S Multidata - Master Ì$MMUL17$-LÎ Master + 17 Slaves Ì$MMUL18$-SÎ Master + 18 Slaves

Datalogic Automation S.r.l. Via Lavino, 265 40050 - Monte S. Pietro Bologna - Italy Setup Procedure Using Programming Barcodes Ed.:

Setup Procedure Using Programming Barcodes 16  ID-NET™ M/S Multidata - Master Ì$MMUL25$-DÎ Master + 25 Slaves Ì$MMUL26$-KÎ Master + 26 Slav

Setup Procedure Using Programming Barcodes 17  ID-NET™ M/S Multidata - Slave Ì$+MUL01$-?Î Slave 1 Ì$+MUL02$-FÎ Slave 2 Ì$+MUL03$-MÎ Slave 3

Setup Procedure Using Programming Barcodes 18  ID-NET™ M/S Multidata - Slave Ì$+MUL08$-pÎ Slave 8 Ì$+MUL09$-wÎ Slave 9 Ì$+MUL10$->Î Sla

Setup Procedure Using Programming Barcodes 19  ID-NET™ M/S Multidata - Slave Ì$+MUL16$-hÎ Slave 16 Ì$+MUL17$-oÎ Slave 17 Ì$+MUL18$-vÎ Slave

Setup Procedure Using Programming Barcodes 20  ID-NET™ M/S Multidata - Slave Ì$+MUL24$-`Î Slave 24 Ì$+MUL25$-gÎ Slave 25 Ì$+MUL26$-nÎ Slav

Setup Procedure Using Programming Barcodes 21 2 TCP/IP ETHERNET INTERFACE TO HOST 2.1 FOR MATRIX 400 OR MATRIX 200 FAMILY READERS For Matrix 40

Setup Procedure Using Programming Barcodes 22 2.2 FOR MATRIX 410 OR MATRIX 210 FAMILY READERS For Matrix 410 or Matrix 210 readers5 having softw

Setup Procedure Using Programming Barcodes 23 For Matrix 410 or Matrix 210 Ethernet readers6 having software 6.10 or later, you can Enable the DHCP

Setup Procedure Using Programming Barcodes 24 2.3 IP ADDRESS ALIGNMENT PROCEDURES FOR CONFIGURATION In order to connect a Matrix reader to VisiS

Setup Procedure Using Programming Barcodes 25 2.3.2 Static IP Addressing (DHCP Disabled) 1. For models connected to QL500 or CBX with BM2x0 modul

iii CONTENTS 1 ID-NET™ NETWORK SETUP USING PROGRAMMING BARCODES...1 1.1 For Matrix 200™ and Matrix 210™...

Setup Procedure Using Programming Barcodes 26 7. Input the IP address from the list in the IP Address field of the Device Ethernet Channel Addr

Setup Procedure Using Programming Barcodes 27 The following figures are examples of these layouts: Point to Point - Matrix 200™ or Matrix 210™ wi

Setup Procedure Using Programming Barcodes 28 ID-NET™ M/S Synchronized Layout with BM200/210 TCP/IP Ethernet Interface to Host ID-NET™ M/S M

Setup Procedure Using Programming Barcodes 29 3 PARAMETER SETTING SUMMARY The network setup through programming barcodes automatically sets all t

www.automation.datalogic.com

iv

Setup Procedure Using Programming Barcodes 1 1 ID-NET™ NETWORK SETUP USING PROGRAMMING BARCODES For Matrix Family readers1 having software 5.60 or

Setup Procedure Using Programming Barcodes 2  ID-NET™ M/S Multidata: Multiple stations – single reader The ID-NET™ interface allows conne

Setup Procedure Using Programming Barcodes 3 1.1 FOR MATRIX 200™ AND MATRIX 210™ AIM 1. Power the reader on. During the reader startup (reset or

Setup Procedure Using Programming Barcodes 4 LEARN 1. Press and hold the X-PRESS™ button to enter the “AutoLearn Mode”. Once button is pressed, t

Setup Procedure Using Programming Barcodes 5 4. The reader is programmed and the AutoLearn Mode ends. The green “ready” LED is on. Programming d