Datalogic QLM500 Manuel d'instructions télécharger pdf (Page 141)

SOFTWARE CONFIGURATION

131

Moving code out of the Field of View:

To correct this result and have the code completely visible in F.O.V., it is possible to follow

one or both the procedures listed below:

reposition the reader

use the Acquisition Trigger Delay by tuning the Delay Time (x100µs)

Figure 127 - Example out of FOV

1 2 ... 136 137 138 139 140 141 142 143 144 145 146 ... 160 161

MATRIX 410™ 1
CONTENTS 3
REFERENCES 6
COMPLIANCE 7
HANDLING 8
GENERAL VIEW 10
1 RAPID CONFIGURATION 11
Required Accessories 12
STEP 2 – CONNECT THE SYSTEM 13
(polarity insensitive) 14
RAPID CONFIGURATION 15
STEP 4 – FOCUS THE READER 16
Locate Function 17
STEP 9 – TEST MODE 27
Host Mode Programming 30
Alternative Layouts 30
Code Quality Verification 30
2 INTRODUCTION 31
INTRODUCTION 33
2.3 ID-NET™ 36
VISISET™ 40
Restore 41
Replacement 42
2.5.1 X-PRESS™ Functions 45
Test Mode (Function 1) 46
Focus/Locate (Function 2) 46
Setup (Function 3) 47
Learn (Function 4) 47
2.5.2 Diagnostic Indication 47
2.6 MODEL DESCRIPTION 48
2.7 ACCESSORIES 48
2.7.1 Lighting System Notes 50
2.8 APPLICATION EXAMPLES 51
2.8.1 Document Handling 51
2.8.4 Direct Part Marking 53
3 INSTALLATION 57
3.2 MECHANICAL DIMENSIONS 58
INSTALLATION 59
[Ø0.32] 60
Figure 43 - Pitch angle 62
Figure 44 - Skew angle 62
Figure 45 - Tilt angle 62
CBX ELECTRICAL CONNECTIONS 63
4.1 POWER SUPPLY 64
4.2 MAIN SERIAL INTERFACE 65
4.2.1 RS232 Interface 66
4.3 ID-NET™ INTERFACE 70
4.3.1 ID-NET™ Cables 70
4.3.2 ID-NET™ Response Time 71
4.5 INPUTS 76
5.1 M16 19-PIN CONNECTOR 83
5.4.1 RS232 Interface 86
5.5 ID-NET™ INTERFACE 90
5.5.1 ID-NET™ Cables 90
5.5.2 ID-NET™ Response Time 91
5.8 INPUTS 97
EXTERNAL TRIGGER 98
Matrix 410™ 98
INPUT DEVICE 99
5.9 OUTPUTS 100
USER INTERFACE 101
MATRIX 410™ REFERENCE MANUAL 102
6 TYPICAL LAYOUTS 103
6.2 PASS-THROUGH 106
6.2.1 Pass-Through on RS232 106
6.3 ID-NET™ 108
 BA600 ID-NET™ Out 109
 BA400 Ext. Power 109
 BA500 Trigger 109
 BA300 Service 109
Fieldbus Interface 113
6.4 RS232 MASTER/SLAVE 114
6.5 MULTIPLEXER 115
6.6 ETHERNET CONNECTION 116
TYPICAL LAYOUTS 117
7 READING FEATURES 118
READING FEATURES 119
7.2.2 1D (Linear) Codes 120
Line Speed 125
8 SOFTWARE CONFIGURATION 127
8.2 INSTALLING VISISET™ 128
8.3 STARTUP 128
8.3.1 VisiSet™ Options 129
8.4 CONFIGURATION 131
Parameters to verify/modify: 133
SOFTWARE CONFIGURATION 135
8.4.3 Calibration 138
8.6 STATISTICS 149
9 MAINTENANCE 150
10 TROUBLESHOOTING 151
11 TECHNICAL FEATURES 154
TECHNICAL FEATURES 155
GLOSSARY 156
UNI EN ISO 14001 160

Commentaires sur ces manuels

Pas de commentaire

Datalogic QLM500 Manuel d'instructions Page 141

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de codes-barres Datalogic QLM500