Datalogic AL5010 Informations techniques Page 37
- Page / 240
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
AccuLazr
™
AL5010 Product Line Manuals Mechanical Installation 29
Installing an AL5010 Scan Head
Perform the electrical installation as outlined in Chapter 4. Once all wiring is
checked for accuracy, install the AL5010 scan head to the mounting base.
You can install the scan head with or without the power disconnected from
the mounting base.
To install a scan head:
1. Carefully align the scan head (1) alignment tabs to the mounting base.
This automatically assures the correct scan head-to-mounting base
connector alignment.
2. Gently, press the scan head down until it firmly connects with the
connector in the mounting base (2).
3. Tighten the two captive screws to secure the scan head to the base.
Do not over tighten.
4. Adjust the UMB so the reader’s laser exit window faces the approximate
location of where the bar-coded packages will appear.
AL5010 Scan Head Installation on Mounting Base
03-AL5010_Mechanical_Installation_R20.doc Accu-Sort Systems, Inc.
- Product Line Manual 1
- Contents 3
- Preface 3
- 1 Introduction 3
- 3 Mechanical Installation 3
- 4 Electrical Installation 4
- 5 Setup 4
- 6 Operations 4
- D Networking Guide 6
- F Installation Drawings 6
- -'37%"3) 7
- Conventions 8
- Customer Service 8
- AL5010 Scan Head 10
- AL5010 Mounting Base 10
- AccuLazr Interface Module 11
- AccuLazr 12
- User Interface 12
- Options and Accessories 14
- 2 Safety 15
- General Precautions 16
- Compliance Requirements 17
- Electrical Safety 17
- Electrostatic Discharge 18
- Basic Rules for ESD Control 18
- Laser Safety 19
- Safety Labels and Locations 20
- 0HFKDQLFDO,QVWDOODWLRQ 21
- Unpacking Instructions 22
- Installation Sequence 23
- Orientation Considerations 24
- Read Range 24
- ← DIRECTION OF TRAVEL → 25
- General Mounting Guidelines 26
- Raster Setup 28
- AL5010 Product Line Manuals 30
- Dimensions and Clearances 35
- Attaching the Mounting Base 35
- Mounting the Tachometer 39
- Mounting the I/O Modules 43
- -'3'3A#191039) 45
- @..59);3A#1'3/))) 45
- !//101.2%5)82B.'C%01.2) 45
- Installation Sequence(s) 46
- Installing Multiple Readers 47
- Basic Interface Module 50
- Enhanced Interface Module 52
- Electrical wiring sequence: 53
- Power Requirements 54
- Trigger Connections 55
- Tachometer Connections 56
- I/O Module Connections 59
- DeviceNet 61
- Profibus 61
- Connecting the AL5010 61
- AL5010 Pin-Out Table 62
- Check Installation 63
- Getting Help 67
- Modify Settings 68
- Settings > Configuration 69
- Settings > Bar Codes 70
- Settings > Modulo Checks 73
- Settings > Match Codes 75
- Settings > Network 79
- Settings > Trigger 82
- Settings > Relay 83
- Settings > Tracking 84
- Settings > Advanced 86
- Settings > Raster 88
- Diagnostics 90
- Diagnostics > Monitor 91
- Diagnostics > Log Viewer 92
- Error Counters 95
- First-time Setup 100
- Operations Checklist 101
- Control Panel Indicators 102
- Backup / Restore Procedures 107
- Standalone Operation 110
- Tracking Operation 111
- Dual X-Scanning Operation 112
- 7 Maintenance 115
- Maintenance Tasks 116
- Cleaning the Exit Window 117
- Cleaning the Tachometer 119
- Tighten Mounting Hardware 119
- Verify Reader Operation 120
- Verify Photoeye Operation 120
- Verify Tachometer Operation 120
- 8 Troubleshooting 121
- (Laser Shutoff) 123
- Monitor 125
- Status LEDs 126
- Read Quality 127
- Log Viewer 128
- Decode/DSP Counters 132
- Update Firmware 133
- Troubleshooting 134
- Discovering the IP Address 136
- !!52&60!2( 137
- AL5010 Interface Module 139
- Other FRUs 139
- Specifications 141
- Power Supply for AL5010 143
- Output Modules 143
- Input Module 143
- Certifications 144
- Read Charts 145
- Combo Read Chart / Table 146
- ™ User Interface AccuLazr 158
- ™ User Interface 151 159
- ™ User Interface 153 161
- ™ User Interface 155 163
- ™ User Interface 157 165
- ™ User Interface 159 167
- ™ User Interface 161 169
- ™ User Interface 163 171
- ™ User Interface 165 173
- ™ User Interface 167 175
- ™ User Interface 169 177
- ™ User Interface 171 179
- ™ User Interface 173 181
- ™ User Interface 175 183
- ™ User Interface 177 185
- ™ User Interface 179 187
- ™ User Interface 181 189
- ™ User Interface 183 191
- ™ User Interface 185 193
- AL5010 Networking Guide 195
- Configuration 196
- Restrictions 197
- TCP/IP Server 198
- TCP/IP Client 199
- UDP Messaging 199
- EtherNet/IP 200
- EtherNet/IP Options 201
- Explicit Messaging Example 202
- I/O Messaging Example 203
- AL5010:C Configuration Data 205
- AL5010:I Input Data 205
- AL5010:O Output Data 205
- EtherNet/IP Object Models 208
- Glossary 208
- Summary of Objects 208
- Definitions 208
- Assembly Object (04 210
- – 4 Instances) 210
- FAST Monitor Configuration 215
- Installation Drawings 217
- 217
- AL5010 Product Line Manual 218
- SOLIDWORKS 219
- ASSEMBLED VIEW 229
- 3ECO 12-40 230
- JG 02/14/12 230
- FIELDBUS 234
- 1 2 3 4 5 235
- 1 INITIAL RELEASE 235
- NRS 11/23/10 235
Produits connexes et manuels pour Lecteurs de codes-barres Datalogic AL5010
(28 pages)
(10 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels